AP5100WG-7

Diodes Incorporated
621-AP5100WG-7
AP5100WG-7

제조업체:

설명:
스위칭 전압 조정기 1.2A Step-Down Conv 1.4MHz Sw Freq

ECAD 모델:
무료 라이브러리 로더를 다운로드하여 이 파일을 ECAD 도구용으로 변환하십시오. ECAD 모델에 대해 자세히 알아보기

재고 상태: 169,054

재고:
169,054 즉시 배송 가능
공장 리드 타임:
24 주 표시된 것보다 많은 수량에 대한 추정 공장 생산 시간입니다.
이 제품은 리드 타임이 깁니다.
최소: 1   배수: 1
단가:
₩-
합계:
₩-
예상 관세:
포장:
전체 릴(3000의 배수로 주문)

가격 (KRW)

수량 단가
합계
컷 테이프/MouseReel™
₩888 ₩888
₩634.9 ₩6,349
전체 릴(3000의 배수로 주문)
₩634.9 ₩1,904,700
† ₩8,000 MouseReel™ 수수료는 장바구니에 더해져 계산됩니다. 모든 MouseReel™ 주문은 취소 및 환불이 불가능합니다.

제품 속성 속성 값 속성 선택
Diodes Incorporated
제품 카테고리: 스위칭 전압 조정기
RoHS:  
SMD/SMT
SOT-26-6
Buck
800 mV to 15 V
1.2 A
1 Output
4.75 V
24 V
400 uA
1.4 MHz
- 25 C
+ 85 C
AP5100
Reel
Cut Tape
MouseReel
브랜드: Diodes Incorporated
제품 유형: Switching Voltage Regulators
팩토리 팩 수량: 3000
하위 범주: PMIC - Power Management ICs
타입: Voltage Converter
단위 중량: 15 mg
제품을 찾음:
유사 제품을 표시하려면 확인란을 하나 이상 선택하십시오.
이 카테고리에 유사 제품을 표시하려면 확인란을 하나 이상 선택하십시오.
속성 선택됨: 0

CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
JPHTS:
8542390990
TARIC:
8542399000
MXHTS:
8542399999
ECCN:
EAR99

AP5100 Step-Down Converter

Diodes Incorporated AP5100 current mode step-down converter with built-in power MOSFET enables the smallest solution size power conversion. With the low series resistance power switch the Diodes Incorporated AP5100 step-down converter enables a constant output current of up to 1.2A over a wide input supply range. The load and line regulation has excellent response time over the operating input voltage and temperature range. 

PAM2306 Dual Step-Down DC-DC Converters

Diodes Incorporated offers a wide range of non-isolated DC-DC Converters. These switching voltage regulator converters feature integrated power switches to make designing easier and to minimize component count. With internal or external compensation, the designer can opt for smaller board space and fewer components or select specific inductor and capacitor values. Higher switching frequencies reduce the output ripple current and allow for comparatively smaller inductors (although special attention has to be given to EMI). Overcurrent, overvoltage, and overtemperature protection increase board reliability and prevent premature failures. A Power Good signal, in combination with an Enable pin, can be used for power sequencing and can warn the processor of possible supply problems and shut down in a controller manner. DC-DC converters include buck, boost, buck/boost, external buck, and external boost.